Strong and Flexible, Nylon 12 Plastic, PA12, Polyamide, PA 2200

Versatile Plastic

Selective Laser Sintering [SLS]

Material info

About Versatile Plastic

Versatile Plastic is a durable nylon plastic that can be used for a wide range of applications, both for prototyping and for end products. Printed using Selective Laser Sintering (SLS), when thin, it’s flexible enough for hinges and springs and when thick, it’s strong enough for structural components. Try the Premium finish for a higher quality look and feel.

Color & Finishes

White
Available in Natural, Processed and Premium finishes
Black
Available in Natural and Premium finishes
Pink
Available in Processed finish
Red
Available in Processed finish
Orange
Available in Processed finish
Blue
Available in Processed finish
Green
Available in Processed finish
Yellow
Available in Processed finish
Purple
Available in Processed finish
Natural
This finish has a slightly rough surface and a matte finish.
Processed
This finish removes some material to create a smoother surface.
Premium
This is the smoothest finish, with good scratch resistance.

Technology

  • Selective Laser Sintering [SLS]

Technical Documents

Material Properties

Tensile modulus (ISO 527)
1700 MPa
Tensile strength (ISO 527)
48 MPa
Elongation at break (ISO 527)
24 %
Flexural modulus (ISO 178)
1500 MPa

Description

Material Highlights
high strength & stiffness applications, skin contact applications, thin features and interlocking parts

Design Guidelines

Bounding Box

Bounding Box Max
650 脳 350 脳 550 mm (Natural White)
180 脳 230 脳 320 mm (Natural Black)
200 脳 150 脳 150 mm (Processed & Premium)
[Parts over 330 mm long in any direction may have a visible line due to our dual laser printer]

Bounding Box Min
X + Y + Z 鈮 7.5 mm (Natural)
X + Y + Z 鈮 25.0 mm and axes must be 鈮 2.5 mm (Processed & Premium)

The bounding box is a 劲爆体育在线直播 imaginary outline of a box that encloses the smallest area occupied by your model. Your model must be within the minimum and maximum bounding box sizes. If the size of the model is close to the maximum bounding box, then the printing orientation will be restricted.

Walls

Supported Wall Thickness Min
0.7 mm
Unsupported Wall Thickness Min
0.7 mm
A supported wall is connected at least on two sides of the wall, while an unsupported wall is connected only on one side of the wall. Walls that do not meet the minimum requirements may not survive printing and cleaning processes. Additionally, models may still be rejected based on the wall geometry of the model. Please consider the size of your model and reinforce the walls or add support structures as needed as minimum guidelines will not always be adequate for large models.

Wires

Supported Wires Min
0.8 mm (Natural)
0.9 mm (Processed & Premium)
Unsupported Wires Min
1.0 mm
A wire is a circular, rectangular or even triangular feature that is thinner in its unconnected directions than its length. A supported wire is connected at least on two sides of the model, while an unsupported wire is connected on one side of the model. Wires that do not meet the minimum requirements may not survive printing and cleaning processes. Additionally, models may still be rejected based on the wire geometry of the model. Please consider the size of your model and reinforce the wires or add support structures as needed as minimum guidelines will not always be adequate for large models.

Details

Details Min Embossed
0.2 mm high & wide for details
0.5 mm high & wide for text
Details Min Engraved
0.2 mm high & wide for details
0.5 mm high & wide for text
For text, the ratio between width and depth, should be 1:1 and sans-serif fonts are preferred for line weight consistency.

Escape Holes

Single Escape Hole Diameter (Min)
4.0 mm
Multiple Escape Hole Diameter (Min)
2.0 mm
Escape holes are necessary to empty the support material of a hollow model. Two escape holes at the opposite ends of the model is optimal for the support removal process. Please consider the size of your model and make the escape holes bigger or add more escape holes as needed as minimum guidelines will not always be adequate for large models.
A single escape hole at the end of a cavity will not allow material in the corners near the escape hole to fully escape. So we recommend multiple escape holes at both ends of the cavity.

Clearance

Min
0.5 mm
Clearance is the space between two individual parts in a model. If the space among the individual parts do not meet the minimum clearance, then parts can fuse together or can be difficult to clean. This is important for movable pieces like hinges, gears, etc.

Sprues

2.0 mm thick, attached in at least 2 places per part.

Sprues are wires that keep two or more parts together. Parts should be connected with a minimum of two sprues each. Please consider the size of your sprues and increase them as needed as minimum guidelines will not always be adequate for large models. If the sprues are within the guidelines and are broken, but there is no damage to your model, we will still ship them as is.

Interlocking & Enclosed Parts

Interlocking
Yes

Enclosed
Yes

Parts in File

Max
Up to 250

Accuracy

Accuracy 卤 0.15 mm, then 卤 0.15% of longest axis
For example: a product with dimensions of 50x50x100 mm can be 0.15 mm + 0.0015*100 mm = 0.3 mm bigger or smaller in any direction.

Related Materials

Also known as Thermoplastic Polyurethane
TPU
Application: Automotive, Medical, Robotics, Hoses, Seals, Footwear, Helmet interiors, Toy tires
Learn More 鈫
Also known as SLS PA11, Nylon 11, EOS PA11, Nylon Polyamide 11
PA11
Application: External medical devices, automotive, sports equipment, loaded functional prototypes, hinges
Learn More 鈫

Newsletter Sign up

Stay up to date on promotions, case studies, and more.